Fundamental Plumber Guide for Bathtub Installation
Fundamental Plumber Guide for Bathtub Installation
Blog Article
Nearly everybody seems to have their own unique assumption involving How to Install a Bathtub Yourself.
Installing a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately tough task. If the old tub is easily obtainable, the task can move quickly; if you have to open up a wall surface to remove the old tub and position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and also set in the new one. See to it you have actually certified yourself for the work as well as are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you start. Chances are you might need a professional plumber to make tube links.
This write-up will certainly help you set up a brand-new bathtub in your washroom if you have actually currently purchased a new tub and do not need to alter the setup of your previous water pipes.
Your devices and material list should make up the following:
Preparing for the Setup
To start with, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be rather troublesome because of the restricted access that is often the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, position the tub in the required setting. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four tiny points.
The following objective is to ensure that the tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile faucet connector to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the water supply and check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub and additionally examine the overflow outlet and the typical outlet for leaks.
Ultimately, fix the bath paneling as described in the maker's user's manual. Tiling and also sealing around the bath tub needs to wait till the bath tub has actually been utilized at least once as this will certainly resolve it right into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the tap and the sink. Secure the faucet in place with the producer provided backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type ought to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture an inflexible seal, triggering the water to penetrate the wall surface between the bath and the tiling, bring about complications with wetness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealant can break fairly very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles making use of waterproof or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our part about How to Install a Bathtub. Thanks a ton for finding the time to read through our posting. Sharing is good. You won't know, you could be doing someone a favor. I praise you for your time. Kindly visit our blog back soon.
Problem solved, just call. Report this page